page 1 of 3 www.aecsensors.com sales department tel: (888) 847-6552 dg82 micro plug-in/pcb automotive relay contacts contact number & arrangement spst-no (1 form a); spdt (1 form c) contact material agni0.15; agni90/10; agsnoino; agcdo max. switching voltage dc 16vdc (current dependent - see fig 3) rated load (max. continuous current) dc1 40a/12vdc (normally open); 30a/12vdc (normally closed) max. switching current 3 make 90a (120a:agsnoino) (normally open); 45a (normally closed) break 40a (normally open contact) / 30a (normally closed contact) minimum load agni0.15: 0.1a/12vdc, agsnoino: 05a/12vdc initial resistance 50m?, max. at 0.1a/6vdc coil rated voltage dc 6...24v must release voltage 0.1un operating range of supply voltage see coil table 1 rated power consumption dc approx. 1.2w (spst-no) / 1.5w (spdt); 1.81w with resistor insulation insulation resistance 100m? at 500vdc, 50%rh dielectric strength coil to contact 500vrms, 1min contact to contact 500vrms, 1min general data operating time (typical) ms 9 release time (typical) ms 7 electrical life 2 ops 2 x 10 5 mechanical life ops 1 x 10 7 dimensions l x w x h 23.5 x 15.7 x 26.0 mm (excluding terminals) weight plug-in: 21g / pcb: 19g approx. ambient temperature storage -40 to 155c operating -40 to 125c (derate above 85c - consult factory) shock resistance functional: 20g 11ms; destructive: 100g vibration resistance da 1.27mm 10-40hz / 40-70hz:5g / da 0.5mm 100-500hz: 10g ? industry standard micro-iso plug-in relay ? up to 120a 12vdc inrush capability ? pcb mounting option ? cost effective ? rohs compliant ref: dg82 102315jhm specifcations are liable to change without notice. e&oe .
ordering codes type contact material contact arrangement cover protec - tion and mounting coil code options d g 8 2 - - - - contact material 10 - agcdo see coil table 1 20 - agni 90/10 70 - agsnoino 80 - agni 0.15 contact arrangement 11 - spdt (1 c/o, 1 form c) 21 - spst-no (1n/o, 1 form a) cover protection category 3 - in cover, sealed - ip67 7 - in cover, dust cover - ip54 connection mode 5 - for pcb 6 - flat blades coil options nil - ul class f coil insulation h - ul class h insulation for higher ambient temperatures - consult factory. parallel component options nil - no option r - resistor (see table 1 for values) d - diode (+85 / -86) dr - diode reversed (-85 / + 86) - standard bd - bidirectional diode dg82 micro plug-in/pcb automotive relay ref: dg82 102315jhm coil data table 1 coil voltage code nominal voltage (vdc) coil resistance (?) 10% must operate voltage max. (vdc) allowable voltage (vdc)* must release voltage min. (vdc) parallel resistor (optional) () 1 form a 1 form c 1 form a 1 form c 1006 6 32 25 3.6 10.4 9.2 0.6 170 1012 12 123 97 7.2 20.4 18.1 1.2 680 1024 24 483 384 14.4 40.4 36.0 2.4 2720 * at ambient temperature of 85c, maximum allowable voltage should be reduced by 28% page 2 of 3 www.aecsensors.com sales department tel: (888) 847-6552 specifcations are liable to change without notice. e&oe .
dg82 micro plug-in/pcb automotive relay american electronic components inc., 1101 lafayette st. elkhart, in46516 page 3 of 3 www.aecsensors.com sales department tel: (888) 847-6552 overall dimensions fig. 1 pcb mounting dimensions fig. 2 wiring diagrams (bottom view) mounting holes (bottom view) dimensions in mm reference curves fig. 3 ref: dg82 102315jhm notes: 1: all parameters, unless otherwise specifed, are measured at ambient temperature of 23 o c. 2: electrical life obtained at resistive or inductive load at 40a, 15vdc with suitable arc suppression circuit attached and with operating frequency of 1 op/sec. 3: maximum make current refers to lamp load inrush current. switching voltage (vdc) switching current (a) spst- no (1 form a) spdt (1 form c) specifcations are liable to change without notice. e&oe .
|
